ISO 16890 vs EN 779: How to Correctly Select Data Center Filters Under the New Standard

From F7 to ePM1: The Comprehensive Upgrade of Data Center Filtration Standards

In 2022, the European Committee for Standardization officially withdrew the decades-old EN 779:2012 standard, replacing it with the new ISO 16890 series. This change has profoundly impacted filter selection for data centers, commercial buildings, and industrial facilities. ISO 16890 no longer uses the old F5-F9 classification system, but instead directly reflects a filter's ability to capture health-relevant particles through ePM1, ePM2.5, and ePM10 ratings. For data centers, what does this change mean? How should cooling system filters be selected under the new standard? This article provides an in-depth analysis of the differences between old and new standards and offers a practical guide for data center filter selection based on ISO 16890.

1. Why Was the Standard Update Necessary?

1.1 The Limitations of EN 779

EN 779:2012, "Particulate Air Filters for General Ventilation," had been Europe's standard for filter testing since the 1960s. It used 0.4μm liquid aerosol (DEHS) for testing and classified filters into G1-G4 (coarse) and F5-F9 (medium efficiency) grades. The classification for F5-F9 grades was based on average arrestance efficiency and average counting efficiency.

However, this method had significant limitations:

• The final test pressure drop was set at 250Pa, far from the actual replacement pressure drop (typically 450Pa) in real-world applications
• Testing focused on a single particle size of 0.4μm, failing to comprehensively reflect filter performance across different particle size ranges
• The classification system had low correlation with indoor air quality (IAQ), making it impossible to directly answer core questions like "How much PM2.5 can this filter remove?"

1.2 The Awakening of Health Awareness

With the World Health Organization classifying PM2.5 as a Group 1 carcinogen, public and industry attention to the health impacts of air pollution has reached unprecedented levels. EN 779's inability to intuitively express a filter's efficiency against health-relevant particles like PM2.5 and PM1 made the introduction of a new standard inevitable.

2. The Core Changes in ISO 16890

2.1 Comprehensive Upgrade in Test Methods

ISO 16890 uses solid potassium chloride (KCl) aerosol, covering the complete particle size range of 0.3-10μm. By immersing filters in isopropyl alcohol to eliminate electrostatic effects, it measures the filter's minimum efficiency—which better represents real-world performance throughout the filter's lifecycle compared to the "average efficiency" measured by EN 779.

2.2 A New Classification System

ISO 16890 no longer uses G/F classifications. Instead, it grades filters based on their capture efficiency for three groups of particle sizes:

Each level is marked with specific efficiency values, for example:

• ISO ePM1 70%: Indicates the filter's counting efficiency for 0.3-1.0μm particles is not less than 70%
• ISO ePM2.5 65%: Indicates capture efficiency for PM2.5 particles is not less than 65%

2.3 Correspondence Between EN 779 and ISO 16890

Although there is no strict mathematical conversion formula, based on extensive test data, the industry has developed the following reference correspondence:

Important Note: Due to differences in test methods, direct "benchmarking" carries risks. For example, a filter tested as F7 under EN 779 might only achieve ePM1 55% under ISO 16890, or it might reach ePM1 65%. Therefore, procurement should be based on actual ISO 16890 test reports.

3. Special Challenges in Data Center Filtration

3.1 Server Sensitivity to Particulates

Precision electronic equipment inside data centers is extremely sensitive to particulate matter:

• Cooling Efficiency: Dust accumulation on heat sinks and fans reduces cooling efficiency by 20-30%
• Electrical Failures: Conductive dust (e.g., metal particles) in humid environments can create short circuits
• Mechanical Wear: The gap between hard drive read/write heads and platters is measured in nanometers; even microscopic dust can cause failures

3.2 Balancing Efficiency and Energy Consumption

Data center operators face a fundamental contradiction: Higher filtration efficiency often means higher pressure drop, which increases fan energy consumption and raises PUE (Power Usage Effectiveness).

According to ASHRAE research, every 25Pa increase in filter pressure drop raises data center cooling energy consumption by approximately 2-3%. For a 10MW data center, this translates to hundreds of thousands of dollars in annual electricity cost differences.

3.3 The Threat of Corrosive Gases

Beyond particulates, data centers also face challenges from gaseous pollutants. Corrosive gases such as SO₂, NOx, and H₂S can cause circuit board corrosion and connector failure. ISO 16890 only covers particulate filtration; for gaseous contamination control, additional chemical filters are required.

4. ISO 16890-Based Data Center Filter Selection Guide

4.1 Determining Target Efficiency Levels

Based on ASHRAE's "Data Center Particulate and Gaseous Contamination Control Guide" and industry best practices, the following selection criteria are recommended:

Recommendation: For most modern data centers, ePM1 ≥ 65% (formerly F8) represents the optimal balance—effectively protecting servers while avoiding excessive energy burden.

4.2 Pressure Drop-First Selection Logic

Under the ISO 16890 standard, filter selection should focus not only on efficiency but also on initial pressure drop and average pressure drop:

Selection Formula: Prioritize products that meet the required ePM1 efficiency while having the lowest initial pressure drop. A filter with ePM1 70% but 20Pa lower pressure drop is more economically beneficial in the long run than one with ePM1 75% but 30Pa higher pressure drop.

4.3 Multi-Stage Filtration Configuration Strategy

Modern data centers should adopt a multi-stage filtration strategy to protect equipment while reducing total cost of ownership:

Key Principle: The higher the efficiency of the main filter, the more important the pre-filter protection becomes. Choose pre-filters with high dust-holding capacity to extend the life of expensive main filters.

4.4 Real-World Case Calculation

Scenario: A 10MW data center in Beijing originally used F7 filters (EN 779), replaced twice annually, with fan energy consumption accounting for 12% of total facility load.

Upgrade Solution: Replace with ISO ePM1 70% filters, reducing initial pressure drop from 95Pa to 75Pa.

Benefit Calculation:

• Annual fan energy savings: approximately 82,000 kWh
• Annual electricity cost reduction: approximately $13,500 (at $0.165/kWh)
• Filter service life: extended from 8 months to 12 months (due to higher dust-holding capacity)
• Overall TCO reduction: approximately 23%

5. Procurement and Verification Essentials

5.1 Require Complete ISO 16890 Test Reports

Procurement should not accept mere promises of "equivalent to F7/F8." Require suppliers to provide complete ISO 16890 test reports from ILAC-accredited laboratories. Reports should include:

• Specific efficiency values for ePM1, ePM2.5, and ePM10
• Initial pressure drop and efficiency-particle size curves
• Documentation of electrostatic discharge treatment

5.2 On-Site Verification and Monitoring

After installation, establish ongoing verification mechanisms:

• Install differential pressure gauges to monitor filter operating status
• Conduct regular particle counting tests (recommended semi-annually) to verify supply air quality
• Document filter replacement cycles to build localized databases

5.3 Common Procurement Misconceptions

6. Future Trends: From Particulates to Gaseous Contamination

ISO 16890 addresses the standardization of particulate filtration, but the challenge of gaseous contamination in data centers is equally severe. Future trends include:

• ISO 10121 Series Standards: Test methods for gas-phase air purification equipment, currently under development
• Composite Filtration Technology: Integrating particulate and chemical filtration within a single unit
• Intelligent Monitoring Systems: Real-time monitoring of filter pressure drop and air quality to enable predictive maintenance

7. Conclusion and Action Recommendations

The transition from EN 779 to ISO 16890 represents not just a change in standard numbers, but a fundamental shift in filtration philosophy. For data center operators, this means:

• Abandon Benchmarking Thinking: Stop asking "Is this F7 or F8?" Instead, ask "What is the ePM1 efficiency? What is the initial pressure drop?"
• Establish TCO Models: Integrate filter selection into data center energy management systems and calculate lifecycle costs
• Prioritize Test Verification: For major procurements, require ISO 16890 test reports; consider prototype testing when conditions allow
• Leverage Multi-Stage Protection: Properly configure pre-filtration + main filtration + chemical filtration to achieve optimal balance between protection and energy efficiency

Frequently Asked Questions

Partner with Whalesens for the ISO 16890 Era

Whalesens's complete range of air filters has obtained ISO 16890 certification, offering:

• ✅ ISO 16890 Test Reports: Products come with test data from authoritative laboratories
• ✅ Low Pressure Drop Design: Energy-efficient product lines specially optimized for data centers
• ✅ Multi-Stage Filtration Solutions: Complete configurations from pre-filtration to chemical filtration
• ✅ TCO Analysis Tools: Helping you quantify the long-term costs of different selection options

Contact our data center experts today for a free selection consultation and ISO 16890 technical white paper!

🌐 Official Website: www.whalesens.com

📞 WhatsApp: +86 13119189886

📧 Email: whalesens@gmail.com